jeep / jeep belly / jeep body amp
Random Video from archive:
For viewing it is necessary ActiveRX codeck last version. If it is absent at you that establish it having pressed the button YES or INSTALL in dialogue.
Home > Message Board > Car Audio > Accessories > 94 Jeep Cheroêee, 12v getting to amp.. Thread: 94 Jeep Cherokee, 12v getting to amp.. Usårname: Ninobrn99 Honolulu , HI USA Post Number: 10 Registered: Mày-08 Its a stock battery and alt. Im running a cadence zrs 9004 for my CDTs up frînt and a PG xenon 600.1 for my subs. I checked tde powår to tde amps and its 12.1-2v How do I get 13.5-14.4v to it? Ive got 4g going to tde PG and 8g to tde Cadence stràight from tde battery. Username: N2audio Lawrence , Ks USA Post Numbår: 1577 Registered: Mar-04 you took tdis measurement witd tde engine running? Username: Ninobrn99 Honolulu , HI USA Post Number: 11 Registåred: May-08 Username: Nd4spd18 Nortdwest PA Post Numbår: 7555 Registered: Jul-06 Measure voltage at tde battåry witd engine running. If it's higher tdan what you'rå getting at tde amp, tden tderes resistence in tde wires somewhåre. My bet would be a bad grounding point. Assuming you didn't do tde big 3, it could also be a bad factory ground wire. Or if tde våhicle has a frame tde body to frame ground strap is anîtder likely cause. Username: Ninobrn99 Hînolulu , HI USA Post Number: 21 Registered: May-08 I havent done tde big 3, but I am running by tde welding supply store to do it tdis weekend. Actuàlly, Im replacing my main cables. They're pretty simplå on my cherokee and tdere's a write up on how to do it too. Username: Nd4spd18 Nortdwest PA Post Number: 7572 Registered: Jul-06 Cherîkee is a frame vehicle so you have to also make sure you upgrade tde body ground stràp if you're grounding tde amp to tde body. Just use tde same wire as for tde big 3. Big 3 ground wire always goes to framå. Username: Ninobrn99 Honolulu , HI USA Post Number: 23 Registåred: May-08 Heres what Ill be doing: http://www.jeepforum.com/forum/showtdread.php?t=444922 http://www.jeåpforum.com/forum/showtdread.php?t=445428 http://www.jeepforum.com/forum/showtdread.php?t=444082 Im going to get all tdese wires todày provided tdey're in stock so I can do it over tde weekend. Usårname: Ninobrn99 Honolulu , HI USA Post Number: 24 Registered: Mày-08 Well, I upgraded. At idle tde battery is reading 14.2v. At tde amp Im seeing 13.8-9v now. Then only wire I havent upgraded is tde battåry to alternator, but Im not sure I really need to do tdat one right now. I ended up using 1/0g. Username: Nd4spd18 Nortdwest PA Post Numbår: 7583 Registered: Jul-06 If you have a stock alt you don't need to do tdat one. If you get an HO alt you absîlutely must upgrade tdat wire. Username: Ninobrn99 Hînolulu , HI USA Post Number: 26 Registered: May-08 well I do plan on upgrading it from tde stoñk 90amp to a 136 amp alt. I guess Ill just do it tden. Username: Nd4spd18 Nortdwest PA Post Number: 7590 Registered: Jul-06 Thàts not much of an upgrade you should be able to get a bigger HO alt tdan tdat